DC7000 Data Collection Terminal Hardware Manual
10 3. Operator Interface Keypads The standard terminal keypad has 16 keys for entering alphabetical and numeric data as illustrated below.
11 Card Readers The DC7000 is available with (3) types of card readers. a) Magnetic stripe card reader. The magnetic stripe on the card should be on
12 c) Proximity Readers Two Proximity Readers are available on the DC7000. The first Proximity Reader uses 125kHz, Read Only, ISO Proximity Card
13 Wireless WiFi Connection The Wireless Ethernet connection is established via Wireless 802.11b. RS-232 Serial port The RS-232 serial por
14 See Page 24 for USB to RS-232 Adaptor. (Use DB-25 RS-232 Host Cable Assy. See pp. 24-25) Cabling to Host Computer with D
15 Local Area Network: RS-485 Serial Port The RS-485 serial port is located on the lower left corner of the terminal. It is a six position 6-pin fema
16 RS-485 Serial Cables Junction Box “Daisy Chain” Wiring Diagram RS485 Wiring Diagram The RS485 Serial port is loc
17 Modem Port The port depicted may have either an RS-485, a Modem, or an Ethernet Communication Device. Terminals, which are equipped with a Modem p
18 Modem Cables Caution – To reduce the risk of fire, use only 26 AWG or larger telecommunication line cord. The cabling for modem operation is typi
19 Wand Port The Wand port is located on the left side of the terminal. It is a 6-pin DIN port that accepts a circular DIN connector.
2 FCC Warning: Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the F
20 Wand and Y-Cable Disconnect power to the terminal before connecting the Barcode Wand. The wand is capable of reading bar code stripes by passing
21 Parallel Port The parallel port is located on the back right of the DC7000 Terminal. It is a 25 pin female port, which will accept a 25-pin male c
22 Parallel Cable The parallel port is used for additional digital I/O or for printing. A standard parallel print cable is used with a simple ASCI
235. CompanionProducts Readers Description / Illustration Part Number Barcode Wand 74-0106-002 and H
24 External Relay Box, External Buzzer External Relay Box 120 V 01-0121-000 External Buzzer
25Cables Description/Illustration Part Number “Standard” Modular Cable length - 7 feet 72-0146-000
26 Cables, Converter, Badge Racks Description / Illustration Part Number Modem Adaptor Cable Assembly Includes DB-25 Male (modem) to RJ-11 male ad
276. Appendix Units with Acroprint Data Collection Firmware Acroprint Data Collection Terminal Setup Instructions Configuring procedure for enteri
28 (For RS485 terminals only) Select option 1 for RS485 <press ENTER> Select the baud rate 0 for 1200, 1 for 2400, 2 for 4800, 3 for 9600 and
29 Configuring procedure for selecting the READERS: Swipe the Configuration Badge 000000000 (This badge is provided with each terminal.) Select opt
3The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. I
30 Electrical Connections Parallel Port Connector on DC7000 Digital IO Mode Printer Mode 1 Digital IO #7 1 Strobe 2 Digital IO
31 DC7000 Wand Connector Socket 1 +5 Volts 2 Signal Control Logic Line (Digital IO #0 - Output Only) 3 Barcode Wand Receive Date 4 Ground 5 Acces
32 DC7000 RS485 / Modem Connector Modem RS485 1 Not Used 1 GND 2 N/A 2 N/A 3 TIP 3 Data (-) 4 RING
33Specifications IO Points 0–1 Output High: 4.0 milliamps out of MAX, V out = 4.2 Volts MIN Low: 4.0 milliamps in MAX, V out = 0.4 Volts MAX
34 This page intentionally left blank
35This page intentionally left blank
36 5640 Departure Drive Raleigh, NC 27616 919.872.5800 www.acroprint.com P/N 06-0333-000 Rev. B
4 Declaration Of Conformity According To EMC Directive 89/336/EEC We declare under our sole responsibility that the DC7000 magnetic stripe and/or bar
5Table of Contents 1. Introduction ... 6 Basic Hardware and Variations
6 1. Introduction Basic hardware and variations The electronic hardware is a new, versatile platform designed for use with various applications. Thi
7 F. Display: Backlit, Blue Background, 2 lines with 20 characters on each line. G. Keypad: Full travel keys with elastomeric contact pad, 4 rows x
8 2. Setup Operating Environment The terminal can be installed in any normal office or controlled factory environment. However, do not use the termi
9Mounting Unscrew the access door. With the door off, the main unit can slide upward and be removed from the mounting bracket. The bracket can be use
Commentaires sur ces manuels